Jeep rear coil over shock gussets.

GenRight rear bump stop kit.

GenRight front Rocker Stomper kit. Low cost solution for bump stops on a Jeep

GenRight outboard Rear shock mount kit for the Jeep TJ, LJ, YJ or CJ-7.

This is the fuel pump adapter ring for any 2005 - Current factory type fuel pump modules on the Jeep TJ, LJ, and JK.

The GenRight Crawler™ Series Fuel Pump Tank rings are great for adapting your factory pump to other aftermarket tanks (metal or plastic).

It is specifically designed and CNC machined from 6061 aluminum alloy to fit the factory fuel pump (includes a machined mating top nut, as pictured) that came in Jeeps between 2005 and 2018.

The 2 piece design is easy to install once the hole is cut and bolt holes drilled.

The APR-1001 model pump ring kit, re-uses the big factory o-ring under the fuel pump and includes a new machined top locking nut.

Great for RCI and JAZ fuel cells.

Includes mounting hardware as shown.

NOTES:

• Not approved for highway use!
• Mounting ring is machined to the same overall height as stock.
• Requires cutting and drilling (on new tanks only) to install properly.
• Requires a gasket or fuel proof silicone sealant between the pump ring plate and the tank surface.
• We also offer an APR-1000 for the older model Jeep fuel pump models '97-'04.

GenRight images and product information are © Copyright GenRight, used with permission.
Additional images and product descriptions are © Bent Fabrication.

Bent Fab is not only a dealer for GenRight we also have a full off road installation shop.
Due to Material Shortages and Shipping Delays we can't guarantee shipping or product availability. All customers will we contacted within 24 business hours with the most update shipping information.

This is our original 3 hole version of the "builders" Triangulated 4 link rear suspension bracket kit.

We have figured out all the mounting points for proper geometry (weight transfer, rear steer and minimal anti-squat, etc.) to make your rig a top notch crawler with awesome articulation AND handle great on the street too!

The main frame control arm mounts are pre-welded to a "C" section of steel to beef up the frame and help distribute the load. You simply slip each mount over the frame and weld them in place! The kit is designed to attach to the frame next to your stock (or aftermarket) transfer case skid plate.

The Bracket Kit FEATURES:

• Each mount is cut at an angle to keep the suspension joints in a "neutral" position so they do not waste any of the joints rotation and cause damage to the joint in those CRAZY articulation spots on the trail.
• Kit can be used with Johnny Joints or FK Heims.
• Simple triangulated 4 link design eliminates the need for a rear trac bar.
• The mounts in this kit are universal and can be cut or trimmed to be mounted in any position on any Jeep TJ, YJ (will also fit CJ, Early Bronco or Toyota but cutting the "C" into an "L").
• These frame side control arm brackets are pre-welded and attach independently and directly to the frame. The mounts DO NOT tie into the transfer case skid plate. This allows unobstructed access to the transmission and transfer case for service.

Kit INCLUDES:

• One pair of Heavy Duty 1/4 & 3/16" thick laser cut, CNC formed control arm mounts and MIG welded.

We recommend the following to help complete the project (hyperlinks listed below):

• Our outboard mounted rear shock kit (RSM-1001) to make relocation (of the spring and shock, if using a coilover type shock) easier and provide better shock dampening.
• Consider converting to coilover shocks at this time. Combined with the above listed shock mount it will make installing this rear suspension much easier.
• Our Rear Sway Bar kit (SWB1003) for better on-road stability.
• Our EXT or COMP stretch package. This will allow you to lengthen the driveline and take advantage of all the rear suspension's articulation.

NOTES:

• Sold in pairs only.
• This kit requires cutting and welding for proper mounting.
• A universal rear axle bridge is now available for Dana 44's and Dana 60's