Home > Rock Krawler
Sort By:
Page of 19
Small Joint Retainer 3/4 and 7/8 Krawler Joints Rock Krawler Small Joint Retainer 3/4 and 7/8 Krawler Joints Rock Krawler

Small Joint Retainer 3/4 and 7/8 Krawler Joints. Rebuild part for 3/4 inch and 7/8 inch Krawler Joint.
Features:

  • Rebuild part for 3/4 inch and 7/8 inch Krawler Joint
  • Sold In Pairs

MSRP Price: $9.49
Our Price: $9.99
Large Joint Retainer 1, 1-1/4 and 1-3/8 Krawler Joints Rock Krawler Large Joint Retainer 1, 1-1/4 and 1-3/8 Krawler Joints Rock Krawler

Large Joint Retainer 1, 1-1/4 and 1-3/8 Krawler Joints
Features:

  • Rebuild part for 1 inch and 1 1/4 inch Krawler Joint
  • Sold In Pairs

MSRP Price: $9.49
Our Price: $9.99
Rock Krawler JL Rear Spring Pad Correction 18-Pres Wrangler JL Rock Krawler JL Rear Spring Pad Correction 18-Pres Wrangler JL

Rock Krawler JL Rear Spring Pad Correction 18-Pres Wrangler JL
Includes:
(2) JL rear spring correction pad

MSRP Price: $19.00
Our Price: $20.00
Rock Krawler Rear Coil Spring Correction Wedges Rock Krawler Rear Coil Spring Correction Wedges

Rear Coil Spring Correction Wedges 07-Present Wrangler JK/JK Unlimited
Our polyurethane rear coil spring correction wedges will fix the following:

  • rear coil spring bowing
  • poor handling due to loss of effective spring rate
  • rear coil spring and rear track bar contact

Includes:
(2) Rear coil spring correction wedges.

MSRP Price: $23.74
Our Price: $24.99
Rock Krawler Sway Bar Strap Kit Rock Krawler Sway Bar Strap Kit

Sway Bar Strap Kit. Hold your sway bar out of the way with The Rock Kralwer Sway Bar Straps. Retains the sway bar and links up and out of the way of axle movement.
Includes:

  • (2) Sway Bar Straps
  • Hardware, and instruction.

MSRP Price: $23.74
Our Price: $24.99
Rock Krawler Upper C's Gussets (Dana 30/44) Rock Krawler Upper C's Gussets (Dana 30/44)

Gussets Upper C's-Dana 30/44 Axles Front 07-Present Wrangler JK/JK Unlimited
Our Upper C Gussets:

  • Are 5/16 inch Thick
  • Strengthen weak factory upper C's
  • Fit both Dana 30 and Dana 44 front axle housings
  • Tie into the spring mounting pads
  • Removal of the upper ball joints is not required

Includes:
(2) 5/16 thick steel upper C gussets.

Our Price: $29.21
Rock Krawler JL Front Spring Pad Correction 18-Pres Wrangler JL Rock Krawler JL Front Spring Pad Correction 18-Pres Wrangler JL

Rock Krawler JL Front Spring Pad Correction 18-Pres Wrangler JL
Includes:

  • (2) JL Front spring correction pad
  • For use with aftermarket JL springs

MSRP Price: $28.50
Our Price: $30.00
Rock Krawler TJ/LJ Weld on Rear Axle Truss Tie In Plate Rock Krawler TJ/LJ Weld on Rear Axle Truss Tie In Plate

The Rock Krawler weld on rear cradle tie in plate is a great way to add style and strength to our Rock Krawler weld on rear cradle. It is made from 1/4 inch thick laser cut steel!
System Benefits:

  • Adds style to the rear axle assembly when our weld on cradle is used
  • Adds strength to the rear cradle for exceptional hard core use

System Includes:
(1) Rear cradle tie in plate made from 1/4 inch thick laser cut steel.
Notes:
Works great with the Rock Krawler weld on rear cradle part number RK00533. May require trimming depending upon what axle it is being used with.

MSRP Price: $37.05
Our Price: $39.00
Pro Krawler Joint 3/4 Inch Shank Right Hand Thread 14 MM Bolt Bore 2.625 Mounting Width Rock Krawler Pro Krawler Joint 3/4 Inch Shank Right Hand Thread 14 MM Bolt Bore 2.625 Mounting Width Rock Krawler

Pro Krawler Joint 3/4 Inch Shank Right Hand Thread. The Pro Krawler Joint is a revolutionary joint manufactured with the tightest tolerances for ultimate consistency. The chromoly joint housings are heat treated for increased strength and then zinc plated for corrosion resistance. The hard chrome plated inner ball is machined from billet 52100 steel for strength and durability. The inner raceway provides wear resistance, high frequency vibration isolation and durability. The body and clevis mounting width ratio of the Pro Krawler Joint is a key design feature which provides up to plus and minus 30 degrees of misalignment. That's a total of 60 degrees of misalignment per side.

  • Universal fitment
  • Corrosion resistant zinc coating
  • Fully machined Chromoly joint housing
  • 14 TPI
  • Right hand thread
  • 14 MM bolt bore
  • 2.625 mounting width
  • Sold individually
  • Jam nuts sold separately
  • Made in the USA

MSRP Price: $37.99
Our Price: $39.99
Pro Krawler Joint 3/4 Inch Shank Left Hand Thread 14 MM Bolt Bore 2.625 Mounting Width Rock Krawler Pro Krawler Joint 3/4 Inch Shank Left Hand Thread 14 MM Bolt Bore 2.625 Mounting Width Rock Krawler

Pro Krawler Joint 3/4 Inch Shank Left Hand Thread. The Pro Krawler Joint is a revolutionary joint manufactured with the tightest tolerances for ultimate consistency. The chromoly joint housings are heat treated for increased strength and then zinc plated for corrosion resistance. The hard chrome plated inner ball is machined from billet 52100 steel for strength and durability. The inner raceway provides wear resistance, high frequency vibration isolation and durability. The body and clevis mounting width ratio of the Pro Krawler Joint is a key design feature which provides up to plus and minus 30 degrees of misalignment. That's a total of 60 degrees of misalignment per side.

  • Universal fitment
  • Corrosion resistant zinc coating
  • Fully machined Chromoly joint housing
  • 14 TPI
  • Left hand thread
  • 14 MM bolt bore
  • 2.625 mounting width
  • Sold individually
  • Jam nuts sold separately
  • Made in the USA

MSRP Price: $37.99
Our Price: $39.99
Pro Krawler Joint 3/4 Inch Shank Right Hand Thread 14 MM Bolt Bore 2.375 Mounting Width Rock Krawler Pro Krawler Joint 3/4 Inch Shank Right Hand Thread 14 MM Bolt Bore 2.375 Mounting Width Rock Krawler

Pro Krawler Joint 3/4 Inch Shank Right Hand Thread. The Pro Krawler Joint is a revolutionary joint manufactured with the tightest tolerances for ultimate consistency. The chromoly joint housings are heat treated for increased strength and then zinc plated for corrosion resistance. The hard chrome plated inner ball is machined from billet 52100 steel for strength and durability. The inner raceway provides wear resistance, high frequency vibration isolation and durability. The body and clevis mounting width ratio of the Pro Krawler Joint is a key design feature which provides up to plus and minus 30 degrees of misalignment. That's a total of 60 degrees of misalignment per side.

  • Universal fitment
  • Corrosion resistant zinc coating
  • Fully machined Chromoly joint housing
  • 14 TPI
  • Right hand thread
  • 14 MM bolt bore
  • 2.375 mounting width
  • Sold individually
  • Jam nuts sold separately
  • Made in the USA

MSRP Price: $37.99
Our Price: $39.99
Pro Krawler Joint 3/4 Inch Shank Left Hand Thread 14 MM Bolt Bore 2.375 Mounting Width Rock Krawler Pro Krawler Joint 3/4 Inch Shank Left Hand Thread 14 MM Bolt Bore 2.375 Mounting Width Rock Krawler

Pro Krawler Joint 3/4 Inch Shank Left Hand Thread. The Pro Krawler Joint is a revolutionary joint manufactured with the tightest tolerances for ultimate consistency. The chromoly joint housings are heat treated for increased strength and then zinc plated for corrosion resistance. The hard chrome plated inner ball is machined from billet 52100 steel for strength and durability. The inner raceway provides wear resistance, high frequency vibration isolation and durability. The body and clevis mounting width ratio of the Pro Krawler Joint is a key design feature which provides up to plus and minus 30 degrees of misalignment. That's a total of 60 degrees of misalignment per side.

  • Universal fitment
  • Corrosion resistant zinc coating
  • Fully machined Chromoly joint housing
  • 14 TPI
  • Left hand thread
  • 14 MM bolt bore
  • 2.375 mounting width
  • Sold individually
  • Jam nuts sold separately
  • Made in the USA

MSRP Price: $37.99
Our Price: $39.99
Pro Krawler Joint 3/4 Inch Shank Right Hand Thread 10 MM Bolt Bore 1.95 Mounting Width Rock Krawler Pro Krawler Joint 3/4 Inch Shank Right Hand Thread 10 MM Bolt Bore 1.95 Mounting Width Rock Krawler

Pro Krawler Joint 3/4 Inch Shank Right Hand Thread. The Pro Krawler Joint is a revolutionary joint manufactured with the tightest tolerances for ultimate consistency. The chromoly joint housings are heat treated for increased strength and then zinc plated for corrosion resistance. The hard chrome plated inner ball is machined from billet 52100 steel for strength and durability. The inner raceway provides wear resistance, high frequency vibration isolation and durability. The body and clevis mounting width ratio of the Pro Krawler Joint is a key design feature which provides up to plus and minus 30 degrees of misalignment. That's a total of 60 degrees of misalignment per side.

  • Universal fitment
  • Corrosion resistant zinc coating
  • Fully machined Chromoly joint housing
  • 14 TPI
  • Right hand thread
  • 10 MM bolt bore
  • 1.95 mounting width
  • Sold individually
  • Jam nuts sold separately
  • Made in the USA

MSRP Price: $37.99
Our Price: $39.99
Pro Krawler Joint 3/4 Inch Shank Left Hand Thread 10 MM Bolt Bore 1.95 Mounting Width Rock Krawler Pro Krawler Joint 3/4 Inch Shank Left Hand Thread 10 MM Bolt Bore 1.95 Mounting Width Rock Krawler

Pro Krawler Joint 3/4 Inch Shank Left Hand Thread. The Pro Krawler Joint is a revolutionary joint manufactured with the tightest tolerances for ultimate consistency. The chromoly joint housings are heat treated for increased strength and then zinc plated for corrosion resistance. The hard chrome plated inner ball is machined from billet 52100 steel for strength and durability. The inner raceway provides wear resistance, high frequency vibration isolation and durability. The body and clevis mounting width ratio of the Pro Krawler Joint is a key design feature which provides up to plus and minus 30 degrees of misalignment. That's a total of 60 degrees of misalignment per side.

  • Universal fitment
  • Corrosion resistant zinc coating
  • Fully machined Chromoly joint housing
  • 14 TPI
  • Left hand thread
  • 10 MM bolt bore
  • 1.95 mounting width
  • Sold individually
  • Jam nuts sold separately
  • Made in the USA

MSRP Price: $37.99
Our Price: $39.99
Pro Krawler Joint 3/4 Inch Shank Right Hand Thread 12 MM Bolt Bore 2 Mounting Width Rock Krawler Pro Krawler Joint 3/4 Inch Shank Right Hand Thread 12 MM Bolt Bore 2 Mounting Width Rock Krawler

Pro Krawler Joint 3/4 Inch Shank Right Hand Thread. The Pro Krawler Joint is a revolutionary joint manufactured with the tightest tolerances for ultimate consistency. The chromoly joint housings are heat treated for increased strength and then zinc plated for corrosion resistance. The hard chrome plated inner ball is machined from billet 52100 steel for strength and durability. The inner raceway provides wear resistance, high frequency vibration isolation and durability. The body and clevis mounting width ratio of the Pro Krawler Joint is a key design feature which provides up to plus and minus 30 degrees of misalignment. That's a total of 60 degrees of misalignment per side.

  • Universal fitment
  • Corrosion resistant zinc coating
  • Fully machined Chromoly joint housing
  • 14 TPI
  • Right hand thread
  • 12 MM bolt bore
  • 2 mounting width
  • Sold individually
  • Jam nuts sold separately
  • Made in the USA

MSRP Price: $37.99
Our Price: $39.99
Pro Krawler Joint 3/4 Inch Shank Left Hand Thread 12 MM Bolt Bore 2 Mounting Width Rock Krawler Pro Krawler Joint 3/4 Inch Shank Left Hand Thread 12 MM Bolt Bore 2 Mounting Width Rock Krawler

Pro Krawler Joint 3/4 Inch Shank Left Hand Thread. The Pro Krawler Joint is a revolutionary joint manufactured with the tightest tolerances for ultimate consistency. The chromoly joint housings are heat treated for increased strength and then zinc plated for corrosion resistance. The hard chrome plated inner ball is machined from billet 52100 steel for strength and durability. The inner raceway provides wear resistance, high frequency vibration isolation and durability. The body and clevis mounting width ratio of the Pro Krawler Joint is a key design feature which provides up to plus and minus 30 degrees of misalignment. That's a total of 60 degrees of misalignment per side.

  • Universal fitment
  • Corrosion resistant zinc coating
  • Fully machined Chromoly joint housing
  • 14 TPI
  • Left hand thread
  • 12 MM bolt bore
  • 2 mounting width
  • Sold individually
  • Jam nuts sold separately
  • Made in the USA

MSRP Price: $37.99
Our Price: $39.99
Pro Krawler Joint 7/8 Inch Shank Right Hand Thread 14 MM Bolt Bore 2.375 Mounting Width Rock Krawler Pro Krawler Joint 7/8 Inch Shank Right Hand Thread 14 MM Bolt Bore 2.375 Mounting Width Rock Krawler

Pro Krawler Joint 7/8 Inch Shank Right Hand Thread. The Pro Krawler Joint is a revolutionary joint manufactured with the tightest tolerances for ultimate consistency. The chromoly joint housings are heat treated for increased strength and then zinc plated for corrosion resistance. The hard chrome plated inner ball is machined from billet 52100 steel for strength and durability. The inner raceway provides wear resistance, high frequency vibration isolation and durability. The body and clevis mounting width ratio of the Pro Krawler Joint is a key design feature which provides up to plus and minus 30 degrees of misalignment. That's a total of 60 degrees of misalignment per side.

  • Universal fitment
  • Corrosion resistant zinc coating
  • Fully machined Chromoly joint housing
  • 14 TPI
  • Right hand thread
  • 14 MM bolt bore
  • 2.375 mounting width
  • Sold individually
  • Jam nuts sold separately
  • Made in the USA

MSRP Price: $37.99
Our Price: $39.99
Pro Krawler Joint 7/8 Inch Shank Left Hand Thread 14 MM Bolt Bore 2.375 Width Rock Krawler Pro Krawler Joint 7/8 Inch Shank Left Hand Thread 14 MM Bolt Bore 2.375 Width Rock Krawler

Pro Krawler Joint 7/8 Inch Shank Left Hand Thread. The Pro Krawler Joint is a revolutionary joint manufactured with the tightest tolerances for ultimate consistency. The chromoly joint housings are heat treated for increased strength and then zinc plated for corrosion resistance. The hard chrome plated inner ball is machined from billet 52100 steel for strength and durability. The inner raceway provides wear resistance, high frequency vibration isolation and durability. The body and clevis mounting width ratio of the Pro Krawler Joint is a key design feature which provides up to plus and minus 30 degrees of misalignment. That's a total of 60 degrees of misalignment per side.

  • Universal fitment
  • Corrosion resistant zinc coating
  • Fully machined Chromoly joint housing
  • 14 TPI
  • Left hand thread
  • 14 MM bolt bore
  • 2.375 mounting width
  • Sold individually
  • Jam nuts sold separately
  • Made in the USA

MSRP Price: $37.99
Our Price: $39.99
Pro Krawler Joint 7/8 Inch Shank Right Hand Thread 12 MM Bolt Bore 2 Mounting Width Rock Krawler Pro Krawler Joint 7/8 Inch Shank Right Hand Thread 12 MM Bolt Bore 2 Mounting Width Rock Krawler

Pro Krawler Joint 7/8 Inch Shank Right Hand Thread. The Pro Krawler Joint is a revolutionary joint manufactured with the tightest tolerances for ultimate consistency. The chromoly joint housings are heat treated for increased strength and then zinc plated for corrosion resistance. The hard chrome plated inner ball is machined from billet 52100 steel for strength and durability. The inner raceway provides wear resistance, high frequency vibration isolation and durability. The body and clevis mounting width ratio of the Pro Krawler Joint is a key design feature which provides up to plus and minus 30 degrees of misalignment. That's a total of 60 degrees of misalignment per side.

  • Universal fitment
  • Corrosion resistant zinc coating
  • Fully machined Chromoly joint housing
  • 14 TPI
  • Right hand thread
  • 12 MM bolt bore
  • 2 mounting width
  • Sold individually
  • Jam nuts sold separately
  • Made in the USA

MSRP Price: $37.99
Our Price: $39.99
Pro Krawler Joint 7/8 Inch Shank Left Hand Thread 12 MM Bolt Bore 2 Mounting Width Rock Krawler Pro Krawler Joint 7/8 Inch Shank Left Hand Thread 12 MM Bolt Bore 2 Mounting Width Rock Krawler

Pro Krawler Joint 7/8 Inch Shank Left Hand Thread. The Pro Krawler Joint is a revolutionary joint manufactured with the tightest tolerances for ultimate consistency. The chromoly joint housings are heat treated for increased strength and then zinc plated for corrosion resistance. The hard chrome plated inner ball is machined from billet 52100 steel for strength and durability. The inner raceway provides wear resistance, high frequency vibration isolation and durability. The body and clevis mounting width ratio of the Pro Krawler Joint is a key design feature which provides up to plus and minus 30 degrees of misalignment. That's a total of 60 degrees of misalignment per side.

  • Universal fitment
  • Corrosion resistant zinc coating
  • Fully machined Chromoly joint housing
  • 14 TPI
  • Left hand thread
  • 12 MM bolt bore
  • 2 mounting width
  • Sold individually
  • Jam nuts sold separately
  • Made in the USA

MSRP Price: $37.99
Our Price: $39.99
Pro Krawler Joint 7/8 Inch Shank Right Hand Thread 14 MM Bolt Bore 2.625 Width Rock Krawler Pro Krawler Joint 7/8 Inch Shank Right Hand Thread 14 MM Bolt Bore 2.625 Width Rock Krawler

Pro Krawler Joint 7/8 Inch Shank Right Hand Thread. The Pro Krawler Joint is a revolutionary joint manufactured with the tightest tolerances for ultimate consistency. The chromoly joint housings are heat treated for increased strength and then zinc plated for corrosion resistance. The hard chrome plated inner ball is machined from billet 52100 steel for strength and durability. The inner raceway provides wear resistance, high frequency vibration isolation and durability. The body and clevis mounting width ratio of the Pro Krawler Joint is a key design feature which provides up to plus and minus 30 degrees of misalignment. That's a total of 60 degrees of misalignment per side.

  • Universal fitment
  • Corrosion resistant zinc coating
  • Fully machined Chromoly joint housing
  • 14 TPI
  • Right hand thread
  • 14 MM bolt bore
  • 2.625 mounting width
  • Sold individually
  • Jam nuts sold separately
  • Made in the USA

MSRP Price: $37.99
Our Price: $39.99
Pro Krawler Joint 7/8 Inch Shank Left Hand Thread 14 MM Bolt Bore 2.625 Width Rock Krawler Pro Krawler Joint 7/8 Inch Shank Left Hand Thread 14 MM Bolt Bore 2.625 Width Rock Krawler

Pro Krawler Joint 7/8 Inch Shank Left Hand Thread. The Pro Krawler Joint is a revolutionary joint manufactured with the tightest tolerances for ultimate consistency. The chromoly joint housings are heat treated for increased strength and then zinc plated for corrosion resistance. The hard chrome plated inner ball is machined from billet 52100 steel for strength and durability. The inner raceway provides wear resistance, high frequency vibration isolation and durability. The body and clevis mounting width ratio of the Pro Krawler Joint is a key design feature which provides up to plus and minus 30 degrees of misalignment. That's a total of 60 degrees of misalignment per side.

  • Universal fitment
  • Corrosion resistant zinc coating
  • Fully machined Chromoly joint housing
  • 14 TPI
  • Left hand thread
  • 14 MM bolt bore
  • 2.625 mounting width
  • Sold individually
  • Jam nuts sold separately
  • Made in the USA

MSRP Price: $37.99
Our Price: $39.99
Pro Krawler Joint 7/8 Inch Shank Right Hand Thread 10 MM Bolt Bore 1.95 Mounting Width Rock Krawler Pro Krawler Joint 7/8 Inch Shank Right Hand Thread 10 MM Bolt Bore 1.95 Mounting Width Rock Krawler

Pro Krawler Joint 7/8 Inch Shank Right Hand Thread. The Pro Krawler Joint is a revolutionary joint manufactured with the tightest tolerances for ultimate consistency. The chromoly joint housings are heat treated for increased strength and then zinc plated for corrosion resistance. The hard chrome plated inner ball is machined from billet 52100 steel for strength and durability. The inner raceway provides wear resistance, high frequency vibration isolation and durability. The body and clevis mounting width ratio of the Pro Krawler Joint is a key design feature which provides up to plus and minus 30 degrees of misalignment. That's a total of 60 degrees of misalignment per side.

  • Universal fitment
  • Corrosion resistant zinc coating
  • Fully machined Chromoly joint housing
  • 14 TPI
  • Right hand thread
  • 10 MM bolt bore
  • 1.95 mounting width
  • Sold individually
  • Jam nuts sold separately
  • Made in the USA

MSRP Price: $37.99
Our Price: $39.99
Pro Krawler Joint 7/8 Inch Shank Left Hand Thread 10 MM Bolt Bore 1.95 Mounting Width Rock Krawler Pro Krawler Joint 7/8 Inch Shank Left Hand Thread 10 MM Bolt Bore 1.95 Mounting Width Rock Krawler

Pro Krawler Joint 7/8 Inch Shank Left Hand Thread. The Pro Krawler Joint is a revolutionary joint manufactured with the tightest tolerances for ultimate consistency. The chromoly joint housings are heat treated for increased strength and then zinc plated for corrosion resistance. The hard chrome plated inner ball is machined from billet 52100 steel for strength and durability. The inner raceway provides wear resistance, high frequency vibration isolation and durability. The body and clevis mounting width ratio of the Pro Krawler Joint is a key design feature which provides up to plus and minus 30 degrees of misalignment. That's a total of 60 degrees of misalignment per side.

  • Universal fitment
  • Corrosion resistant zinc coating
  • Fully machined Chromoly joint housing
  • 14 TPI
  • Left hand thread
  • 10 MM bolt bore
  • 1.95 mounting width
  • Sold individually
  • Jam nuts sold separately
  • Made in the USA

MSRP Price: $37.99
Our Price: $39.99
Pro Krawler Joint 7/8 Inch Shank Right Hand Thread 12 MM Bolt Bore 2 Mounting Width Rock Krawler Pro Krawler Joint 7/8 Inch Shank Right Hand Thread 12 MM Bolt Bore 2 Mounting Width Rock Krawler

Pro Krawler Joint 7/8 Inch Shank Right Hand Thread. The Pro Krawler Joint is a revolutionary joint manufactured with the tightest tolerances for ultimate consistency. The chromoly joint housings are heat treated for increased strength and then zinc plated for corrosion resistance. The hard chrome plated inner ball is machined from billet 52100 steel for strength and durability. The inner raceway provides wear resistance, high frequency vibration isolation and durability. The body and clevis mounting width ratio of the Pro Krawler Joint is a key design feature which provides up to plus and minus 30 degrees of misalignment. That's a total of 60 degrees of misalignment per side.

  • Universal fitment
  • Corrosion resistant zinc coating
  • Fully machined Chromoly joint housing
  • 14 TPI
  • Right hand thread
  • 12 MM bolt bore
  • 2 mounting width
  • Sold individually
  • Jam nuts sold separately
  • Made in the USA

MSRP Price: $37.99
Our Price: $39.99
Pro Krawler Joint 7/8 Inch Shank Leftt Hand Thread 12 MM Bolt Bore 2 Mounting Width Rock Krawler Pro Krawler Joint 7/8 Inch Shank Leftt Hand Thread 12 MM Bolt Bore 2 Mounting Width Rock Krawler

Pro Krawler Joint 7/8 Inch Shank Left Hand Thread. The Pro Krawler Joint is a revolutionary joint manufactured with the tightest tolerances for ultimate consistency. The chromoly joint housings are heat treated for increased strength and then zinc plated for corrosion resistance. The hard chrome plated inner ball is machined from billet 52100 steel for strength and durability. The inner raceway provides wear resistance, high frequency vibration isolation and durability. The body and clevis mounting width ratio of the Pro Krawler Joint is a key design feature which provides up to plus and minus 30 degrees of misalignment. That's a total of 60 degrees of misalignment per side.

  • Universal fitment
  • Corrosion resistant zinc coating
  • Fully machined Chromoly joint housing
  • 14 TPI
  • Left hand thread
  • 12 MM bolt bore
  • 2 mounting width
  • Sold individually
  • Jam nuts sold separately
  • Made in the USA

MSRP Price: $37.99
Our Price: $39.99
Rock Krawler TJ Rear Stainless Steel Long Travel Brake Line Rock Krawler TJ Rear Stainless Steel Long Travel Brake Line

The Rock Krawler TJ long travel stainless steel brake line kit uses some of the longest stainless steel brake lines in the industry. They are perfect for those looking to get longer brake lines or improve braking ability.

System Benefits:

  • Long travel stainless steel brake lines
  • Improved braking ability over rubber lines
  • Fits TJ's with up to 7 inches of lift

System Includes:
(2) Front long travel stainless steel brake lines
(1) Rear long travel stainless steel brake line

MSRP Price: $42.75
Our Price: $45.00
Rock Krawler LJ Rear Stainless Steel Long Travel Brake Line Rock Krawler LJ Rear Stainless Steel Long Travel Brake Line

The Rock Krawler rear long travel stainless steel brake line is one of the longest rear stainless steel brake lines in the industry. They are perfect for those of you who are looking to get longer brake lines or improve your braking ability.

System Benefits:

  • Long travel stainless steel rear brake line.
  • Improved braking ability over a standard rubber line.

System Includes:
(1) rear long travel stainless steel brake line

Notes:

  • Valid for LJ's with up to 7 inches of lift.

MSRP Price: $42.75
Our Price: $45.00
Rock Krawler JK Rear Frame Side Track Bar Bracket Rock Krawler JK Rear Frame Side Track Bar Bracket

JK Rear Stretch Frame-Side Trackbar Bracket
Includes:
(1) JK rear frame-side trackbar relocation bracket

MSRP Price: $42.75
Our Price: $45.00
Rock Krawler TJ/LJ Rear Sway Bar Links (3.5-5.5 Inch Lift) Rock Krawler TJ/LJ Rear Sway Bar Links (3.5-5.5 Inch Lift)

The Rock Krawler 3.5 inch to 5.5 inch rear sway bar end links are some of the strongest sway bar end links in the industry. They use a 5/8 inch solid center pin where most other companies use 1/2 inch at best. The ends use a heavy wall tube so failure is not an option!
System Benefits:

  • Improved off-road ability.
  • Tigther on highway handling from improved rigidity.

System Includes:
(1) pair of rear extended sway bar end links.

MSRP Price: $46.55
Our Price: $49.00